Go Kart Clutches

Centrifugal Clutch 3/4?? Bore 12 Tooth for 35 Chain, Common clutch for 2-6.5 HP engis 2300 RPM. The 12T clutch has a broached 3/16″ keyway with two set screw holes located 90 degrees apart
Our go-kart clutch is made of high-grade steel, heavy-duty and long lasting. It can withstand the strain and heat caused by friction, once the clutch engages
Perfect for Go Kart, Minibike and Fun Kart. Fits Honda GX160, GX200, GX 140, GX120, GC160, GC190, Harbor Freight Greyhound 196cc, Harbor Freight Predator 212cc, briggs and Stratton Tecumseh engis and 2-6.5 HP with 3/4?? shaft
Also fits any other engis with 3/4 crank shaft and 3/16?? key way, most 5.5 HP clos, 6.5 HP clos and 4-7HP motors in all brands
Go cart clutch kit includes two set screws, but chain is not included. The two set screw holes are tapped 1/4″-28
Our go-kart clutch is made of high-grade steel, heavy-duty and long-lasting. It can withstand the strain and heat caused by friction, once the clutch engages.
Go-kart clutches work best on these types of go-karts:
1. Racing Go-Kart
2. Homemade Go-Karts
Specification:
Two set screws are included, but chain is Not included.
3/4″ bore12 TeethFor # 35 Chain
Fits:
This Clutch Will Fit 2 – 6.5 HP Engis Honda GC160, GC190, GX120, GX140, GX160, GX200 Also will fit Briggs & Stratton and 2 – 6.5 HP With 3/4″ Shaft Also Will Fit Tecumseh Engis 2 – 6.5 HP With 3/4″ Shaft And Any Other Engis With 3/4 Crank Shaft and 3/16″ Key Way. Package includes: 1 x Go Kart Clutch
Read more
Warm Tips
Oiling the clutch is extremely important
Besides checking the condition of your clutch from time to time, it??s also important to keep it properly oiled. If heat damage occurs, the clutch will ver disengage and the machi will start taking off by itself as soon as you start the engi. This is very dangerous! You can see heat damage inside the clutch drum, the metal turns from black to a blue color.
Where do you oil the clutch
Behind the snap ring, xt to the sprocket teeth at the end of the clutch. There’s an internal bronze bushing behind the snap ring that requires lubrication and it’s up to you to put it there each time.ver oil the large ventilation holes on the drum. This will cause your clutch to not engage properly anymore.
Oil the chain at the same time
It’s a good idea to oil the chain at the same time. If the chain gets kinky from lack of oil it should be replaced before it damages the clutch sprocket. A w chain is cheaper than a w clutch.
Read moreNote:he Centrifugal Clutch 3/4″ eds be oiled before use.Before ordering please check your crankshaft size.Don’t put oil inside the clutch holes: The holes on the drum are to let the hot air out of the clutch. DO NOT SQUIRT OIL IN THESE HOLES. When oil gets in the drum portion of the clutch it will cause excessive slippage, which means undue heat will be gerated.
Read more
Warm Tips: About the Clutch Slipping:Don’t try and reduce a go-kart speed by limiting the travel of the gas pedal or by putting a restrictor in the carburetor to limit full rpm. Either of these methods will result in the clutch slipping, which is self-destructive. A clutch eds full rpm to lock up as quickly as possible to be able to start to cool down. To slow down a go-kart you would ed to purchase a gear reduction unit, which is like training wheels on a go-kart until the driver gets used to how the go-kart handles. A gear reduction unit can reduce the speed of the go-kart in half.
About the Clutch Smoke:The clutch weight rpm just isn??t excessive sufficient. The engi not being highly effective sufficient sometimes is the result of a mismatch in ratios to the rear-drive wheels. So the true motive is that the ratio just isn??t steep sufficient, and subsequently, the engi smokes the clutch.The treatment for the primary clutch smoking drawback is to change the driveli in order that the geral ratio is steeper. The easy technique is to extend the rear sprocket diameter.So the clutEngagement rpm must be taken under consideration in any other case the clutch will smoke on the secondary jackshaft mounting place.
Go Kart Clutch 3/4 Bore 10T with #40 41 420 Chain
Go Kart Clutch 3/4 Bore 12T with #35 Chain
Bore Diameter
3/4″ Bore 3/4″ Bore
Sprocket
10 Teeth 12 Teeth
Go with Chain
Fit Chain
#40 41 420 Chain #35 Chain
Chai
Length:
3 Feet 4 Feet