Locate the Drive Belt: The drive belt is usually located near the engine and the rear axle of the go-kart. Loosen Components: Use the appropriate

Remove the Old Ignition Coil: Use a wrench or socket set to carefully remove any bolts securing the old ignition coil to the engine. Keep

Remove the old clutch: To access the clutch, you may need to remove the chain guard and any other obstructions. Using a clutch removal tool

Remove the old exhaust pipe (if applicable): If you are replacing an existing exhaust pipe, you’ll need to remove it first. Depending on the go-kart’s

Prepare the go-kart: Ensure the go-kart is parked on a flat surface and the engine is off. If necessary, disconnect the spark plug wire to

1. Start by taking off the small screws that are holding the air box to the engine. Be sure to take off the screws evenly

1. Begin by gathering all the necessary parts and tools that you will need, such as a torque wrench, socket set, sprocket, key, and a

1. Start by loosening the lug nuts on the wheel. Depending on your kart, the lug nuts may be on the outside or inside of

1. Park the kart on a flat, level surface and set the parking brake. 2. Remove the old tires from the wheels. Use a tire

1. Start by loosening the steering wheel nut using a wrench. 2. Remove the steering wheel nut and any washers that may be present. 3.

1. Place the go-kart on a level surface and turn off the engine. 2. Locate the two mounting points for the belt. They are usually

1. Wheel Feels Loose When Car Is Jacked Up If you’re not sure if you have bad tie rods and you’ve got a little bit

Clutches The clutch serves two purposes: Engage the load – Make the go kart go Disengage the Load – Make the gokart stop or slow

There is a lot of misinformation out there on this subject. The reason for this is because the clutch and how it is wearing is

Some of the symptoms of master cylinder failure you should be on the lookout for include: 1. Check Engine Light Indicates The check engine light

Step 1: Put on protective gear, switch off the engine, and remove the air filter’s housing along with any hoses and linkages and the bottom

Chain Care First, each chain has quite a number of steel pins that are rubbing inside of “steel tubes”. They just rub back and forth,

Go-karts are some of the simplest and most primitive vehicles you can find. However, karts have developed over time and there have been some more

It’s absolutely vital that your kart’s drive chain is properly set. Not only does it help to prolong its and your sprockets’ life, but it

1. Park the vehicle on a flat surface: As with most types of maintenance on any car, the safety of the person doing the work,

Here are five tips from us to help make your go kart handle better: 1. Adjusting the Front End (Balance) When you steer your go

1. Remove The Engine From The Chassis The first step is to clean the back of the engine. You will see a ton of dirt and

1. Slide the Clutch Onto the Crankshaft Now that the preparation is out of the way, you can proceed to slot the clutch onto the

Measuring the Wheel Hub The wheel hub is the central rotating part that holds the wheel in place. It contains bearings and connections for ABS

Your vehicle’s air filter is critical to maintaining engine performance. It allows clean air to combine with fuel, combust, and produce the vehicle’s power. Over

Go-karts are often thought of as mini cars since they’re both vehicles meant for driving. While they share some of the same parts, like a

Clutch stuck to the crankshaft: This is not an uncommon problem, people ask all the time about how to remove your go-kart clutch. It could

A go-kart clutch is an important mechanical component, as it engages the power transmission. It does this by transmitting the torque from the crankshaft of

Place your go kart on it’s trolley and place 2 steel pipes (or something similar) underneath either side of the kart to lift the chassis

Weld the Axle Stubs to the Tubing The process to weld the axle stubs (bolts) to the fixed axle is very important because this will